kt13-63-centrifugal-blower.jpg
  1. GENERAL

  2. KT13-63 CENTRIFUGAL BLOWER IS DESIGNED BASE ON ADVANTAGES OF FOREIGN SAMPLE AND HAVE A SUCCESSFUL TRIAL PRODUCED. THE MAYOR PART WERE ADOPT, NO PLATING WITH HIGH QUALITY. THE STEEL PLATE WITH RIVET JOINT. SO THAT THE BLOWER WILL NOT HAPPEN RUST EATEN IN USING PROCEED.  IT CAN AVOID SHORT COMING FROM CONVENTIONAL ONES, SUCH AS PAINTING AND WELDING RUST EATEN ARE PEELED OFF TO MAKE GAS AND DUST INCREASE. IT CAN ASSURE TRANSPORTING GAS CLEANING. AS THE BLOWER IS ADOPTED A ADVANTAGES OF CONSTRUCTION AND REASONABLE PNEUMATIC DESIGNED. IT HAS THE ADVANTAGED OF POWER ECONOMY, LOW NOISE, LIGHT WEIGHT, HANDLE ACCESSIBLY, RELIABLE RUNNING.

    IT IS SUITABLE FOR AIR-COOLING COIL, AIR-COOLING GENERATOR ROOM AND REMOVAL IN PUBLIC PLACE

  3. TECHNICAL DATA

  4. Model Voltage Capacity Pressure Speed Power Weight
    V m³ / h Pa RPM KW Kg
    KT 13 – 63 No 2 220 1900 – 2500 I 150 – 950 2800 1,5 79
    KT 13 – 63 No 2 380 1450 335 1400 0,25 13
    KT 13 – 63 No 2 380 900 – 2500 I 150 – 950 2800 1,5 29
    KT 13 – 63 No 2,5 220 2500 480 1400 0,55 18,5
    KT 13 – 63 No 2,5 380 4000 2107 2800 3 50
    KT 13 – 63 No 2,5 380 2500 480 1400 0,55 18,5
    KT 13 – 63 No 3,15 220 5700 840 1400 1,5 37
    KT 13 – 63 No 3,15 380 6500 360 1400 3 53
    KT 13 – 63 No 3,15 380 5700 840 1400 1,5 37
    KT 13 – 63 No 4 380 10450 980 1400 5,5 98

  5. MOUNTING AND DIMENSION

  6. kt13-63

    No A A I A2 B B1 B2 C D E F H I 4-d
    2 181 160 90 306 286 90 397 87 110 255 315 343 Ø 12
    2,5 215 194 90 370 349 90 430 105 105 305 370 420 Ø 12
    3,15 255 234 90 455 434 90 511 135 205 380 470 520 Ø 12
    4 309 288 90 564 543 90 715 162 215 470 540 649 Ø 12

  7. ASSEMBLY AND USE

    • Before Installing. Must Check The Connection Between PartsIS Firm. See IF THE IMPELLER TOUCH CASING. AS SOON AS FINDING PROBLEM. MUST REMOVE AND ADJUST.
    • THE SELECTED POWER FOR BLOWER. THAT IS FOR MECHANICAL DAMAGE. OTHER DAMAGE AND STORAGE CAPACITY AT THE. SPECIAL OPERATING MODE AND NOT FOR SELECTED POWER OF BLOWER AT THE DAMPER. TO SEVERAL
    • CONTROL. THE CURRENT AT THE OPERATING PROCESS. MAKE SURE NO LESS THAN RATING VALUE FOR MOTOR OR MAY DAMAGE THE MOTOR. IF THE OPERATING MODE OFFER CHANGE. INSTALLING SHUTTER AT THE INLET PORT AND OPENING THE INLET BY BIG OR SMALL TO ADJUST THE CURRENT.
    • THERE ARE THREE DIFFERENT ANGLES TO CHANGE FOR BLOWER TO ASSEMBLY POSITION. THE COMSTER JUST REMOVE THE BOLT SHOW AS FIGURE 1. TURN THE VOLUTE CASING TO THE POSITION OF THE UNDER LIGHT INDICATES CENTRE AND TIGHTEN THE BOLT.
    • POSTERIORI SWITCH ON. SEE IF THE ROTATING DIRECTION OF BLADES TALLY WITH TECHNICAL SPECIFICATION IN ORDER TO AV0ID DAMAGE SPARE PARTS.
    • WHEN HEAVY VIBRATION OF BLADES AND ABNORMAL NOISE OR SMELL. OCCURS DURING OPERATION. CUT OFF ELECTRIC IMMEDIATELY AND LOOK FOR CAUSE